3D AutoCAD 2004/2005: One Step at a Time

  < Day Day Up > 

  1. Use the following information to create the drawing in Figure 17.8.1d. Save the drawing as MyTee in the C:\Steps\Lesson17 folder.

    Figure 17.8.1a

    Figure 17.8.1b

    Figure 17.8.1c

    Figure 17.8.1d: Socket Weld Tee

    1.1  

    Layer Information:

    Layer Name

    Color

    Linetype

    0

    7 (white)

    Continuous

    Border

    5 (blue)

    Continuous

    Cl

    3 (green)

    Center

    Dim

    5 (blue)

    Continuous

    Hatch

    32

    Continuous

    Marker

    6 (magenta)

    Continuous

    Ob

    1 (red)

    Continuous

    Text

    6 (magenta)

    Continuous

     

    1.2  

    Limits: 0,0 to 17,11
     

    1.3  

    Grid spacing = 1/4"
     

    1.4  

    Text sizes = 3/8", 1/4", 3/16", 1/8"

     

    1.5  

    Font: Times New Roman

     

    1.6  

    Hatching information

    1.6.1  

    Pattern = ANSI32

     

    1.6.2  

    Scale = 1"

     

    1.6.3  

    Angle = 0

  2. Start a new drawing from scratch.

    2.1  

    Create the following setup:

    2.1.1  

    Use a 1½"=1'-0" scale on an A-size sheet of paper (8½x11)

     

    2.1.2  

    Grid: 1" (snap as needed)

     

    2.1.3  

    These layers:

    Layer

    Name

    Color Linetype

    0

    7 (white)

    Continuous

    Cl

    6 (magenta)

    Center2

    Const

    1 (red)

    Continuous

    Obj1

    4 (cyan)

    Continuous

    Obj3

    1 (red)

    Continuous

    Text

    2 (yellow)

    Continuous

     

    2.2  

    Use this information for the Grade hatching:

    Pattern: EARTH

    Scale: 8.0000

    Angle: 45
     

    2.3  

    Use this information for the sand hatching:

    Pattern: AR-SAND

    Scale: 0.5000

    Angle: 0
     

    2.4  

    Use the Times New Roman font. Large text should plot at ¼"; small text should plot at 1/8".
     

    2.5  

    Create the Exterior Slab drawing shown in Figure 17.8.2a. Save it as MySlab in the C:\Steps\Lesson17 folder.

    Figure 17.8.2a: Exterior Slab

  3. Start a new drawing from scratch. Using the same information you used in the Exterior Slab drawing in Exercise 2, create the Concrete Pier Footing drawing in Figure 17.8.3a.

    Figure 17.8.3a: Concrete Pier Footing

    3.1  

    Use this information to hatch the concrete:

    Pattern: AR-CONC

    Scale: 0.5000

    Angle: 0
     

    3.2  

    Save the drawing as MyFooting in the C:\Steps\Lesson17 folder.

  4. Open the Cabin-hatch.dwg file in the C:\Steps\Lesson17 folder. Use the following information to complete the drawing. The completed elevations are shown in Figures 17.8.4a & b. (See if you can add a chimney on your own.)

    4.1  

    Create these additional layers:

    Layer Name

    Color

    Linetype

    Hatch1

    85

    Continuous

    Hatch2

    22

    Continuous

    Hatch3

    44

    Center

    Hatch4

    214

    Continuous

     

    4.2  

    Hatching information:

    4.2.1  

    Doors:

    Pattern: AR-RROOFScale = ¼" Angle = 90° Layer = Hatch3
     

    4.2.2  

    Roof:

    Pattern: AR-RSHKEScale = 1/16"Angle = 0° Layer = Hatch3
     

    4.2.3  

    Facade:

    Pattern: AR-BRELMScale = 1/8" Angle = 0° Layer = Hatch2
     

    4.2.4  

    Curtains:

    Pattern: STARSScale = 1"Angle = 90° Layer = Hatch4
     

    4.2.5  

    Gables:

    Pattern: ANSI31Scale = 1" Angle = 45°Layer = Hatch2
     

    4.2.6  

    Doorknobs are on the Hatch1 layer.

    Figure 17.8.4a: Front Elevation

    Figure 17.8.4b: Side Elevation

  5. Using what you've learned, create the drawings in Figures 17.8.5a to 17.8.5h. The grid, where shown, is 2".

    Figure 17.8.5a: Curb Cut

    Thanks to Tilco Vanguard of Snohomish, Washington and Jon Julnes for allowing us to use this drawing.

    Figure 17.8.5b: Transverse Contraction Joint

    Figure 17.8.5c: Integral Curb

    Figure 17.8.5d: Longitudinal Joint

    Figure 17.8.5e: Guardrail Detail

    Figure 17.8.5f: Longitudinal Joint

    Figure 17.8.5g: Concrete Header

    Figure 17.8.5h: Median Detail

    Special thanks to Randy Behounek at the Sarpy County Surveyors Office in Papillion, Nebraska for permission to use Figures 17.8.5b to 17.8.5h drawings.

  6. Using what you've learned, create the drawing shown in Figure 17.8.6a.

    Figure 17.8.6a: Plot Plan

 < Day Day Up > 

Related

Категории