| | As mentioned earlier, the Initial System Loader (ISL) is run after the PDC. You would normally just run an "autoboot" sequence from ISL, however, there are a number of commands you could run from the ISL prompt. |
Picking up where we left off in the preceding example, we have chosen to BOot off of device p0 and interact with IPL as shown in the following example: Main Menu: Enter command or menu > bo p0 Interact with IPL (Y, N, or Cancel)?> y Booting... Boot IO Dependent Code (IODC) revision 1 HARD Booted. ISL Revision A.00.38 OCT 26, 1994 ISL> ? HELP Help Facility LS List ISL utilities AUTOBOOT Set or clear autoboot flag in stable storage AUTOSEARCH Set or clear autosearch flag in stable storage PRIMPATH Modify primary boot path in stable storage ALTPATH Modify alternate boot path in stable storage CONSPATH Modify system console path in stable storage DISPLAY Display boot and console paths in stable storage LSAUTOFL List contents of autoboot file FASTSIZE Sets or displays FASTSIZE 800SUPPORT Boots the s800 Support Kernel from the boot device 700SUPPORT Boot the s700 Support Kernel from the boot device READNVM Displays contents of one word of NVM READSS Displays contents of one word of stable storage LSBATCH List contents of batch file BATCH Execute commands in batch file LSEST List contents of EST (Extended Self Test) file EST Execute commands in EST (Extended Self Test) file Enter 'LS' to see a list of the ISL utilities. ISL> Issuing a ? produces a list of ISL commands that we could issue. Issuing the DISPLAY command shows the boot and console paths and LS lists the ISL utilities available, as shown in the following example: ISL> display Fastsize value is 0000000F Autoboot is ON (enabled) Autosearch is ON (enabled) Primary boot path is 0/0/1/1.2.0.0.0.0.0 Primary boot path is (hex) 0/0/1/1.2.0.0.0.0.0 Alternate boot path is 0/0/2/0.2.0.0.0.0.0 Alternate boot path is (hex) 0/0/2/0.2.0.0.0.0.0 System console path is 0/0/4/0.0.0.0.0.0.0 System console path is (hex) 0/0/4/0.0.0.0.0.0.0 ISL> ls Utilities on this system are: filename type start size created ==================================================== ODE -12960 584 1216 00/01/21 16:45:48 HPUX -12928 3480 800 99/10/28 15:23:53 ISL> DISPLAY produced the information we expected based on what we had seen in the preceding section produced by PDC. LS produced two utilities available to us: ODE and HPUX. ODE is the Offline Diagnostics Environment. The following example shows listing the ODE utilities available on the system by running ODE, the HELP command to see what commands are available, and LS to list the ODE utilities: ISL> ode *************************************************************************** ****** ****** ****** Offline Diagnostic Environment ****** ****** ****** ****** (C) Copyright Hewlett-Packard Co 1993-2000 ****** ****** All Rights Reserved ****** ****** ****** ****** HP shall not be liable for any damages resulting from the ****** ****** use of this program. ****** ****** ****** ****** TC Version A.02.20 ****** ****** SysLib Version A.00.74 ****** ****** Loader Version A.00.59 ****** ****** Mapfile Version A.01.23 ****** ****** ****** *************************************************************************** Type HELP for command information. ODE> help ODE Help Basic Commands -------------- HELP -- Prints detailed information to the screen, when "help <command>" or "help <var>" is typed LS -- List modules available on boot medium <Module_Name> -- Load and initialize a module by typing its name (For more help, type "help module_name") MENU -- Launch ODE's ease-of-use interface RUN -- Run a module (after setting desired environment variables) Control-Y|Control-C -- Abort an ODE command; pause a module run RESUME -- Restart a paused module DISPLOG -- After running a module, display contents of a log EXIT -- Return to next higher level prompt Environmental Variables ----------------------- SHOWSTATE -- Display the value of the following environment variables: LOOP -- Run a test this many times ERRPRINT [ON|OFF] -- Print low-level error messages to console (primarily for manufacturing use) ERRNUM [ON|OFF] -- Print one-line, numbered errors to the console Continue ([y]/n)? y ERRPAUSE [ON|OFF] -- Pause module upon error detection ERRONLY [ON|OFF] -- Print ONLY error messages; disable non-error and isolation message printing INFOPRINT [ON|OFF] -- Print informational messages to the console ISOPRINT [ON|OFF] -- Print fault isolation messages to the console ISOPAUSE [ON|OFF] -- Pause module when isolation message is generated LOGSIZE -- Set the size of a message log DEFAULT -- Reset environment variables to default state ODE> ls Modules on this boot media are: filename type size created description ----------------------------------------------------------------------------- MAPPER2 TM 126 00/01/21 64 bit version of the system mapping ut IOTEST2 TM 88 00/01/21 64 bit version that runs ROM-based self PERFVER2 TM 124 00/01/21 64 bit version that runs ROM-based self ODE> When we ran ODE in this example and issued LS the three utilities at the end of the example were listed. I always load ODE as a part of system installations to help in the event of a possible system hardware problem that an HP CE may need to diagnose. Next, we'll proceed with the boot process by running the HPUX utility: |