Viewing SDLC Status Information

Problem

You want to check the status of an SDLC device on your router.

Solution

You can get a lot of useful SDLC information simply by looking at the interface:

Router>show int serial1 Serial1 is up, line protocol is up Hardware is HD64570 Description: Connection to three remote SDLC devices MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation SDLC, loopback not set Router link station role: PRIMARY (DCE) Router link station metrics: slow-poll 30 seconds T1 (reply time out) 3000 milliseconds N1 (max frame size) 12016 bits N2 (retry count) 20 poll-pause-timer 200 milliseconds poll-limit-value 1 k (windowsize) 7 modulo 8 sdlc vmac: 4000.CCCC.00-- sdlc addr 20 state is CONNECT cls_state is CLS_IN_SESSION VS 0, VR 0, Remote VR 0, Current retransmit count 0 Hold queue: 0/200 IFRAMEs 5025/618 TESTs 0/0 XIDs 0/0, DMs 0/0 FRMRs 0/0 RNRs 15/2 SNRMs 0/0 DISC/RDs 0/0 REJs 0/0 Poll: clear, Poll count: 0, ready for poll, chain: 22/21 sdlc addr 21 state is CONNECT cls_state is CLS_IN_SESSION VS 0, VR 0, Remote VR 0, Current retransmit count 0 Hold queue: 0/200 IFRAMEs 127/15 TESTs 0/0 XIDs 0/0, DMs 0/0 FRMRs 0/0 RNRs 1/0 SNRMs 0/0 DISC/RDs 0/0 REJs 0/0 Poll: clear, Poll count: 0, ready for poll, chain: 20/22 sdlc addr 22 state is SNRMSENT cls_state is CLS_CONNECT_RSP_PEND VS 0, VR 0, Remote VR 0, Current retransmit count 0 Hold queue: 0/200 IFRAMEs 25/0 TESTs 0/0 XIDs 0/0, DMs 0/0 FRMRs 0/0 RNRs 0/0 SNRMs 0/0 DISC/RDs 0/0 REJs 0/0 Poll: clear, Poll count: 0, ready for poll, chain: 21/20 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 01:05:31 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue :0/40 (size/max) 5 minute input rate 6 bits/sec, 2 packets/sec 5 minute output rate 3 bits/sec, 1 packets/sec 157210 packets input, 315708 bytes, 0 no buffer Received 287021 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 156918 packets output, 307682 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DCD=up DSR=up DTR=up RTS=down CTS=up

 

Discussion

This recipe shows the output of a show interface command for the multidrop configuration shown in Recipe 15.6. The first thing to look at is the first line, which reports that the interface is up and line protocol is also up. In general, these values are affected by physical issues such as whether the cabling is correctly connected, clocking, and the choice of NRZ or NRZI line coding. The other thing to look at if you have trouble bringing the line up is the duplex setting of the interface. On Cisco routers, SDLC uses full duplex by default. To change this to half duplex, use the sdlc hdx command:

Router-A#(config)#interface Serial1 Router-A#(config-if)#sdlc hdx

In the output of the show interface command above, you can immediately see that there are three SDLC addresses configured, with hexadecimal addresses 20, 21, and 22. In this particular case, only the first two stations are shown in a connected state, and the third is not responding. The router is trying to contact it, so it is listed in a SNRMSENT state. This means that the router has sent a Set Normal Response Mode (SNRM) request to initialize the Physical Unit (PU). Table 15-5 shows all of the possible states for SDLC devices.

Table 15-5. SDLC device states

State Description
CONNECT Circuit initialization has completed successfully for this device.
DISCONNECT The router is not attempting to communicate with the device.
DISCSENT The router has sent a disconnection request to the device, but has not yet received a response.
SNRMSEEN The router has received a connection request from the device (the router must be secondary, and the device must be primary).
SNRMSENT The router has sent a connection request to the device, but has not yet received a response (the router must be primary to send a SNRM).
THEMBUSY The device has sent an RNR frame.
USBUSY The router has sent an RNR frame.
BOTHBUSY The router and the device are both sending RNR frames.
XIDSENT For PU2.1 devices, this means that the router has sent the XID to the device.
XIDSTOP For PU2.1 devices, the device has sent its XID to the router.

In normal conditions, all of your devices should be in the CONNECT state, so this is a good thing to check when debugging an SDLC problem. If a device is connected, but you suspect that there is a problem with it, there is a useful EXEC command that is effectively an SDLC version of PING:

Router#sdlc test serial 1 20 SDLC Test for address C1 completed Frames sent=10 Frames received=10

This command sends short SDLC frames out the specified interface (in this case Serial1) addressed to the desired destination address (in this case, 20). If the device is online and the circuit is configured correctly, then you should see the same number of frames received as sent. By default, it sends 10 frames. You can change the number and content of these frames, but usually this simple form is sufficient to see if there are problems reaching the device.

The most common problems with an SDLC connection are mismatched XID or SDLC addresses. Sometimes you will encounter physical problems caused by either a bad cable or electrical noise. And the other most common issues are caused by clock rate problems (either too fast or too slow for the attached devices), or an incorrect choice of NRZ or NRZI line coding. It is usually best to start with the physical layer and see if the interface is coming up at all. If the interface won't come up, or comes up but won't stay up, then look for physical problems such as these. If the interface comes up but you can't communicate with the devices, look for problems with XID values and SDLC addresses.

See Also

Recipe 15.6

Категории